|
OPEN
END RIVETS
|
| Also referred to as "Break Stem" rivets, this style is the most widely used. They are simple to install & offer the best variety of material combinations. The flange (head) braces against the topside of the material while the rivet body forms a bulge on the backside, creating a tight clamp for two or more layers. For softer materials create a larger bearing surface with a "large flange" rivet, or use a washer to help absorb the impact from installation. Need a smooth surface? Choose a countersunk rivet. Will the rivet be in contact with food or exposed to moisture? Choose stainless steel. |
|
ALUM ALUM
|
ALUM
STEEL |
STEEL
STEEL |
STAINLESS
STAINLESS |
DIAMETER
|
GRIP RANGE
|
"L"
|
|
AA42D
|
AS42D
|
SS42D
|
TT42D
|
1/8"
|
.062-.125
|
0.275
|
|
AA43D
|
AS43D
|
SS43D
|
TT43D
|
1/8"
|
.125-.187
|
0.337
|
|
AA44D
|
AS44D
|
SS44D
|
TT44D
|
1/8"
|
.188-.250
|
0.400
|
|
AA42LF
|
-
|
-
|
-
|
1/8"
|
.062-.125
|
0.275
|
|
AA44LF
|
-
|
-
|
TT44LF
|
1/8"
|
.188-.250
|
0.400
|
|
AA45D
|
-
|
SS45D
|
-
|
1/8"
|
.250-.312
|
0.462
|
|
AA46D
|
AS46D
|
SS46D
|
TT46D
|
1/8"
|
.250-.375
|
0.525
|
|
AA48D
|
AS48D
|
SS48D
|
TT48D
|
1/8"
|
.375-.500
|
0.650
|
|
AA410D
|
AS410D
|
-
|
TT410D
|
1/8"
|
.500-.625
|
0.775
|
|
AA52D
|
AS52D
|
SS52D
|
TT52D
|
5/32"
|
.062-.125
|
0.300
|
|
AA53D
|
AS53D
|
SS53D
|
TT53D
|
5/32"
|
.125-.187
|
0.362
|
|
AA54D
|
AS54D
|
SS54D
|
TT54D
|
5/32"
|
.188-.250
|
0.425
|
|
AA56D
|
AS56D
|
SS56D
|
TT56D
|
5/32"
|
.250-.375
|
0.550
|
|
AA58D
|
AS58D
|
SS58D
|
TT58D
|
5/32"
|
.375-.500
|
0.675
|
|
AA510D
|
AS510D
|
-
|
-
|
5/32"
|
.500-.625
|
.800
|
|
-
|
AS512D
|
-
|
-
|
5/32"
|
.626-.750
|
0.925
|
|
AA62D
|
AS62D
|
SS62D
|
TT62D
|
3/16"
|
.062-.125
|
0.325
|
|
AA64D
|
AS64D
|
SS64D
|
TT64D
|
3/16"
|
.126-.250
|
0.450
|
|
AA64LF
|
AS64LF
|
SS64LF
|
TT64LF
|
3/16"
|
.126-.250
|
0.450
|
|
AA66D
|
AS66D
|
SS66D
|
TT66D
|
3/16"
|
.250-.375
|
0.575
|
|
AA66LF
|
AS66LF
|
SS66LF
|
TT66LF
|
3/16"
|
.250-.375
|
0.575
|
|
AA68D
|
AS68D
|
SS68D
|
TT68D
|
3/16"
|
.375-.500
|
0.700
|
|
AA68LF
|
AS68LF
|
SS68LF
|
TT68LF
|
3/16"
|
.375-.500
|
0.700
|
|
AA610D
|
AS610D
|
SS610D
|
TT610D
|
3/16"
|
.500-.625
|
0.825
|
|
AA610LF
|
AS610LF
|
SS610LF
|
TT610LF
|
3/16"
|
.500-.625
|
0.825
|
|
AA612D
|
AS612D
|
-
|
TT612D
|
3/16"
|
.625-.750
|
0.950
|
|
AA612LF
|
AS612LF
|
-
|
TT612LF
|
3/16"
|
.625-.750
|
0.950
|
|
-
|
-
|
SS84D
|
-
|
1/4"
|
.125-.250
|
0.500
|
|
-
|
-
|
SS86D
|
-
|
1/4"
|
.250-.375
|
0.625
|
|
-
|
-
|
SS86LF
|
-
|
1/4"
|
.250-.375
|
0.625
|
|
-
|
-
|
SS88D
|
-
|
1/4"
|
.375-.500
|
0.750
|
|
-
|
-
|
SS88LF
|
-
|
1/4"
|
.375-.500
|
0.750
|
|
-
|
-
|
SS810D
|
-
|
1/4"
|
.500-.625
|
0.875
|
|
-
|
-
|
SS812D
|
-
|
1/4"
|
.625-.750
|
1.000
|
|
-
|
-
|
SS812LF
|
-
|
1/4"
|
.625-.750
|
1.000
|
|
-
|
-
|
SS814D
|
-
|
1/4"
|
.750-.875
|
1.125
|
|
-
|
-
|
SS816D
|
-
|
1/4"
|
.876-1.00
|
1.250
|
ADDITIONAL OPEN END RIVETS
| COPPER BRASS |
STAINLESS STEEL |
STAINLESS STAINLESS |
DIAMETER | GRIP RANGE | "L" (MAX) |
| TT3.6D | 3MM | 1MM-3MM | 6.4MM | ||
| TT3.8D | 3MM | 3MM-5MM | 8.4MM | ||
| TT3.10D | 3MM | 5.5MM-7.5MM | 10.4MM | ||
| TT3.12D | 3MM | 6MM-9MM | 12.4MM | ||
| CB42D | TS42D | 1/8 | .062-.125 | 0.275 | |
| TS43D | 1/8 | .125-.187 | 0.337 | ||
| CB44D | TS44D | 1/8 | .188-.250 | 0.400 | |
| TS64D | 3/16" | .125-.250 | 0.450 |
**Call for quotes on Pure Metric Rivets 1-800-405-7964
ROUND BACK UP PLATES
|
P/N
|
MATERIAL
|
I.D.
|
O.D.
|
THICKNESS
|
|
A-4
|
ALUMINUM
|
0.131
|
0.375
|
0.062
|
|
A-6
|
ALUMINUM
|
0.194
|
0.500
|
0.062
|
|
S-4
|
STEEL
|
0.131
|
0.375
|
0.062
|
COMMON OPEN END DIMENSIONS
|
 |
||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||
| NOTE: Nominal dimensions are shown. Contact factory for engineering tolerances. | |||||||||||||||||||||||||||||||
OPEN END CROSS REFERENCE
Numbers remain a constant with any rivet manufacturer.
Use the chart below to identify the material combination required.
| MATERIAL | IFS | POP | CHERRY | GESIPA | MARSON | AFC | CELUS |
| ALUM/ALUM | AA-D | AD-ABS | AAP-- | GAMD-A | AB-A | ABA | A/A-D |
| ALUM/STEEL | AS-D | AD-BS | BSP-- | GSMD-A | AB-- | ABS | A/S-D |
| COPPR/BRASS | CB-D | USP-- | CB-B | ||||
| STNLS/STNLS | TT-D | SSD-SSBS | CCP-- | GSSMD-SS | SSB-S | FBF | SS/SS-D |
| STNLS/STEEL | TS-D | SSD-BS | CSP-- | GSMD-SS | FBS | SS/S-D | |
| STEEL/STEEL | SS-D | SD-BS | SSP-- | GSMD-S | SB-- | SBS | S/S-D |
| *LARGE FLANGE | "LF" |
"L"
|
"LF"
|
"L"
|
"L"
|
"L"
|
"LF"
|
| *COUNTERSUNK | "C" |
"C"
|
"C"
|
"C"
|
"C"
|
"C"
|
"C"
|
* Replaces the "D" to identify the head style
| EXAMPLE #1 | AA42D | ABA42 | A/A42 | AAP-42 | GAMD42A | AB4-2A | AD42ABS |
| EXAMPLE #2 | SS66LF | SBS66L | S/S66LF | SSL-66 | GSMD66L | SB6-6L | SD66BSLF |
Home | ArcOne | IFS | Updates | Contact | Distributors | Search | Literature
